Is drag coefficient lowest at zero angle of attack? Planned maintenance scheduled April 17/18, 2019 at 00:00UTC (8:00pm US/Eastern) Announcing the arrival of Valued Associate #679: Cesar Manara Unicorn Meta Zoo #1: Why another podcast?How do insects decrease aircraft performance?How to draw NACA 6-Series Airfoils?How can the zero-lift drag coefficient (parasitic drag) be calculated?What is the relation between the Lift Coefficient and the Angle of Attack?Is it possible to fly horizontally with zero angle of attack?How to find trim condition of a sectional airfoil without knowing the angle of attack?What is the effect of flow separation on lift, pressure distribution and drag?How can the zero-lift drag coefficient (parasitic drag) be calculated?Do negative angles-of-attack create lift?How do you calculate the lift coefficient of an airfoil at zero angle of attack?Calculating induced drag approximation using XFoil generated parasitic dragDoes speed or angle of attack generally have the greatest impact on total induced drag?What's the theoretical background of the critical angle of attack?
How do I keep my slimes from escaping their pens?
What are the options for player characters to create traps?
How remove lines which are not equal in two buffers?
How much radiation do nowadays nuclear physics experiments impose on researcher
Left action of a group on permutation representation
What are the motives behind Cersei's orders given to Bronn?
What is a 'tuning' of a guitar and why would you use it? Doesn't it make it more difficult to play?
How to pronounce "criar"?
Is there a documented rationale why the House Ways and Means chairman can demand tax info?
Does polymorph use a PC’s CR or its level?
Why does Python start at index 1 when iterating an array backwards?
Regex in IF condition in awk
Why is there no army of Iron-Mans in the MCU?
Bold symbols in LuaLaTeX with setmathfont
He is picky about food(,) so he only eats what he likes
Why don't the Weasley twins use magic outside of school if the Trace can only find the location of spells cast?
Should gear shift center itself while in neutral?
Project this triangle on surface of a sphere
How should I respond to a player wanting to catch a sword between their hands?
How can I make names more distinctive without making them longer?
When to stop saving and start investing?
How to motivate offshore teams and trust them to deliver?
Truth table with logical gates for a traffic light
If A makes B more likely then B makes A more likely"
Is drag coefficient lowest at zero angle of attack?
Planned maintenance scheduled April 17/18, 2019 at 00:00UTC (8:00pm US/Eastern)
Announcing the arrival of Valued Associate #679: Cesar Manara
Unicorn Meta Zoo #1: Why another podcast?How do insects decrease aircraft performance?How to draw NACA 6-Series Airfoils?How can the zero-lift drag coefficient (parasitic drag) be calculated?What is the relation between the Lift Coefficient and the Angle of Attack?Is it possible to fly horizontally with zero angle of attack?How to find trim condition of a sectional airfoil without knowing the angle of attack?What is the effect of flow separation on lift, pressure distribution and drag?How can the zero-lift drag coefficient (parasitic drag) be calculated?Do negative angles-of-attack create lift?How do you calculate the lift coefficient of an airfoil at zero angle of attack?Calculating induced drag approximation using XFoil generated parasitic dragDoes speed or angle of attack generally have the greatest impact on total induced drag?What's the theoretical background of the critical angle of attack?
$begingroup$
The drag coefficient of a symmetric airfoil is lowest when its angle of attack is zero. I'm not sure if this is true in general.
aerodynamics airfoil drag angle-of-attack
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
add a comment |
$begingroup$
The drag coefficient of a symmetric airfoil is lowest when its angle of attack is zero. I'm not sure if this is true in general.
aerodynamics airfoil drag angle-of-attack
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago
add a comment |
$begingroup$
The drag coefficient of a symmetric airfoil is lowest when its angle of attack is zero. I'm not sure if this is true in general.
aerodynamics airfoil drag angle-of-attack
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$endgroup$
The drag coefficient of a symmetric airfoil is lowest when its angle of attack is zero. I'm not sure if this is true in general.
aerodynamics airfoil drag angle-of-attack
aerodynamics airfoil drag angle-of-attack
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 18 hours ago
simple jacksimple jack
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 18 hours ago
simple jacksimple jack
183
asked 18 hours ago
simple jacksimple jack
183
183
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
simple jack is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago
add a comment |
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago
add a comment |
1 Answer
1
active
oldest
votes
$begingroup$
Obviously, drag should be smallest for symmetrical airfoils at zero angle of attack.
However, most airfoils have camber, and then the lowest drag is at positive lift coefficients in case of positive camber. Where that point is exactly depends on many parameters; in case of laminar airfoils even local imperfections can have a noticeable effect. Generally, the lowest drag can be found at the angle of attack where the stagnation point is exactly at the center of the leading edge, where the local curvature is highest. A deviation from this point will force the flow on one side to negotiate this point of highest curvature all by itself, resulting in a suction peak which will increase the losses in the boundary layer.
This is a theoretical drag polar (calculated with XFOIL) of an airfoil with a 20% camber flap at different settings and a Reynolds number of 1.5 million. The laminar bucket is clearly visible and produces a range of lift coefficients with nearly identical drag. The small waviness at the lower end of the laminar bucket is an artificial result of smoothing the plot.
What is obvious is how camber shifts the area of minimum drag up and down. If you use the right side of the plot to find the angle of attack of minimum drag, you will find that this is not constant but goes down as flap angles go up. For the 0° flap polar it is at about -2° AoA. This is caused by the induced angle of attack which increases with the lift coefficient.
The 6-series NACA airfoils were the first to be systematically designed with the pressure distribution in mind, and the design lift coefficient is where the condition of the ideal stagnation point location is met. This is indicated by the digit right after the hyphen in the airfoil name: Divide this digit by 10 and you have the lift coefficient of minimum drag.
Example: The $63_1-412$ airfoil has its lowest drag at a lift coefficient of 0.4.
If you want to know the angle of attack with the lowest drag of a whole airplane, this is a very different matter and needs to include the drag due to lift, which is of course smallest at the zero lift polar point.
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
$endgroup$
add a comment |
Your Answer
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "528"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
simple jack is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f62357%2fis-drag-coefficient-lowest-at-zero-angle-of-attack%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
Obviously, drag should be smallest for symmetrical airfoils at zero angle of attack.
However, most airfoils have camber, and then the lowest drag is at positive lift coefficients in case of positive camber. Where that point is exactly depends on many parameters; in case of laminar airfoils even local imperfections can have a noticeable effect. Generally, the lowest drag can be found at the angle of attack where the stagnation point is exactly at the center of the leading edge, where the local curvature is highest. A deviation from this point will force the flow on one side to negotiate this point of highest curvature all by itself, resulting in a suction peak which will increase the losses in the boundary layer.
This is a theoretical drag polar (calculated with XFOIL) of an airfoil with a 20% camber flap at different settings and a Reynolds number of 1.5 million. The laminar bucket is clearly visible and produces a range of lift coefficients with nearly identical drag. The small waviness at the lower end of the laminar bucket is an artificial result of smoothing the plot.
What is obvious is how camber shifts the area of minimum drag up and down. If you use the right side of the plot to find the angle of attack of minimum drag, you will find that this is not constant but goes down as flap angles go up. For the 0° flap polar it is at about -2° AoA. This is caused by the induced angle of attack which increases with the lift coefficient.
The 6-series NACA airfoils were the first to be systematically designed with the pressure distribution in mind, and the design lift coefficient is where the condition of the ideal stagnation point location is met. This is indicated by the digit right after the hyphen in the airfoil name: Divide this digit by 10 and you have the lift coefficient of minimum drag.
Example: The $63_1-412$ airfoil has its lowest drag at a lift coefficient of 0.4.
If you want to know the angle of attack with the lowest drag of a whole airplane, this is a very different matter and needs to include the drag due to lift, which is of course smallest at the zero lift polar point.
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
$endgroup$
add a comment |
$begingroup$
Obviously, drag should be smallest for symmetrical airfoils at zero angle of attack.
However, most airfoils have camber, and then the lowest drag is at positive lift coefficients in case of positive camber. Where that point is exactly depends on many parameters; in case of laminar airfoils even local imperfections can have a noticeable effect. Generally, the lowest drag can be found at the angle of attack where the stagnation point is exactly at the center of the leading edge, where the local curvature is highest. A deviation from this point will force the flow on one side to negotiate this point of highest curvature all by itself, resulting in a suction peak which will increase the losses in the boundary layer.
This is a theoretical drag polar (calculated with XFOIL) of an airfoil with a 20% camber flap at different settings and a Reynolds number of 1.5 million. The laminar bucket is clearly visible and produces a range of lift coefficients with nearly identical drag. The small waviness at the lower end of the laminar bucket is an artificial result of smoothing the plot.
What is obvious is how camber shifts the area of minimum drag up and down. If you use the right side of the plot to find the angle of attack of minimum drag, you will find that this is not constant but goes down as flap angles go up. For the 0° flap polar it is at about -2° AoA. This is caused by the induced angle of attack which increases with the lift coefficient.
The 6-series NACA airfoils were the first to be systematically designed with the pressure distribution in mind, and the design lift coefficient is where the condition of the ideal stagnation point location is met. This is indicated by the digit right after the hyphen in the airfoil name: Divide this digit by 10 and you have the lift coefficient of minimum drag.
Example: The $63_1-412$ airfoil has its lowest drag at a lift coefficient of 0.4.
If you want to know the angle of attack with the lowest drag of a whole airplane, this is a very different matter and needs to include the drag due to lift, which is of course smallest at the zero lift polar point.
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
$endgroup$
add a comment |
$begingroup$
Obviously, drag should be smallest for symmetrical airfoils at zero angle of attack.
However, most airfoils have camber, and then the lowest drag is at positive lift coefficients in case of positive camber. Where that point is exactly depends on many parameters; in case of laminar airfoils even local imperfections can have a noticeable effect. Generally, the lowest drag can be found at the angle of attack where the stagnation point is exactly at the center of the leading edge, where the local curvature is highest. A deviation from this point will force the flow on one side to negotiate this point of highest curvature all by itself, resulting in a suction peak which will increase the losses in the boundary layer.
This is a theoretical drag polar (calculated with XFOIL) of an airfoil with a 20% camber flap at different settings and a Reynolds number of 1.5 million. The laminar bucket is clearly visible and produces a range of lift coefficients with nearly identical drag. The small waviness at the lower end of the laminar bucket is an artificial result of smoothing the plot.
What is obvious is how camber shifts the area of minimum drag up and down. If you use the right side of the plot to find the angle of attack of minimum drag, you will find that this is not constant but goes down as flap angles go up. For the 0° flap polar it is at about -2° AoA. This is caused by the induced angle of attack which increases with the lift coefficient.
The 6-series NACA airfoils were the first to be systematically designed with the pressure distribution in mind, and the design lift coefficient is where the condition of the ideal stagnation point location is met. This is indicated by the digit right after the hyphen in the airfoil name: Divide this digit by 10 and you have the lift coefficient of minimum drag.
Example: The $63_1-412$ airfoil has its lowest drag at a lift coefficient of 0.4.
If you want to know the angle of attack with the lowest drag of a whole airplane, this is a very different matter and needs to include the drag due to lift, which is of course smallest at the zero lift polar point.
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
$endgroup$
Obviously, drag should be smallest for symmetrical airfoils at zero angle of attack.
However, most airfoils have camber, and then the lowest drag is at positive lift coefficients in case of positive camber. Where that point is exactly depends on many parameters; in case of laminar airfoils even local imperfections can have a noticeable effect. Generally, the lowest drag can be found at the angle of attack where the stagnation point is exactly at the center of the leading edge, where the local curvature is highest. A deviation from this point will force the flow on one side to negotiate this point of highest curvature all by itself, resulting in a suction peak which will increase the losses in the boundary layer.
This is a theoretical drag polar (calculated with XFOIL) of an airfoil with a 20% camber flap at different settings and a Reynolds number of 1.5 million. The laminar bucket is clearly visible and produces a range of lift coefficients with nearly identical drag. The small waviness at the lower end of the laminar bucket is an artificial result of smoothing the plot.
What is obvious is how camber shifts the area of minimum drag up and down. If you use the right side of the plot to find the angle of attack of minimum drag, you will find that this is not constant but goes down as flap angles go up. For the 0° flap polar it is at about -2° AoA. This is caused by the induced angle of attack which increases with the lift coefficient.
The 6-series NACA airfoils were the first to be systematically designed with the pressure distribution in mind, and the design lift coefficient is where the condition of the ideal stagnation point location is met. This is indicated by the digit right after the hyphen in the airfoil name: Divide this digit by 10 and you have the lift coefficient of minimum drag.
Example: The $63_1-412$ airfoil has its lowest drag at a lift coefficient of 0.4.
If you want to know the angle of attack with the lowest drag of a whole airplane, this is a very different matter and needs to include the drag due to lift, which is of course smallest at the zero lift polar point.
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
answered 14 hours ago
Peter KämpfPeter Kämpf
162k12411656
162k12411656
add a comment |
add a comment |
simple jack is a new contributor. Be nice, and check out our Code of Conduct.
simple jack is a new contributor. Be nice, and check out our Code of Conduct.
simple jack is a new contributor. Be nice, and check out our Code of Conduct.
simple jack is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Aviation Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faviation.stackexchange.com%2fquestions%2f62357%2fis-drag-coefficient-lowest-at-zero-angle-of-attack%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
-aerodynamics, airfoil, angle-of-attack, drag
$begingroup$
Welcome to Av.SE!
$endgroup$
– Ralph J
18 hours ago